![]() ![]() Remove type section as described in Changing the Type Section. Remove cover as described in Unlock and Remove the Cover. Unplug the unit from the AC electrical outlet. Model 2121 Time Recorder User’s Guide Change the Motor 1. Press type section lock lever as shown on page 3 and lift type section slightly and move it to the right to release the hinge pins from their sockets. Model 2121 Time Recorder User’s Guide Change the Type Section If the type section needs servicing, you can easily remove and change it without sending the entire unit for service. Use a pointed object to remove the small cotter pins that hold the ribbon spools. Remove cover and lift type section as described in Unlock and Remove the Cover and Lift Type Section. When the time comes, it is easy to change. With normal use, a ribbon should last for many months or even years. Model 2121 Time Recorder User’s Guide Change the Ribbon Lathem time recorders have self-reversing ribbons. 9 Close and Lock the Unit 9.1 9.2 Slide the case cover on the unit. If it does not, start again with Lift the Type Section. Verify that the clock face time matches the printed time. Push lever on front of the unit down to make a print. 8.1 8.3 8.4 When the clock advances to the next minute, you hear a distinct click. Test that Clock Is Now Set Correctly 8.2 Insert a card or piece of paper below the print ribbon. Plug the clock into an AC electrical outlet. 7.5 Firmly push it into the clock until it clicks. 7.4 Tip: Turn spools to tighten ribbon before lowering type section to avoid catching the ribbon. Model 2121 Time Recorder User’s Guide 7.2 While holding the type section up, release the latch by slightly pushing it in the direction, as shown below. Each minute will make a distinct click as you rotate the wheel. 6.2 Use your fingers or a pointed object to rotate the main setting wheel clockwise until it advances the time on the clock face to the current time. Advance Print Wheels and Hands 6.1 Turn the main setting wheel, as shown below, to advance both the clock face and the print wheels together. 5.2 Rotate the clock setting wheel counter-clockwise to set the clock time to the print time you previously set. Caution: Do not manually turn the hands on the clock face. Set Hands on Clock Face 5.1 Locate the setting wheel on the right side below the clock face. This prevents the print wheels from being manually turned. Model 2121 Time Recorder User’s Guide 4.3 When finished, release the red overthrow lever by gently pulling it toward you until it clicks. Rotate each wheel with your fingers or a pointed object clockwise until the correct day and time are aligned at the center position. The characters in the center position of each wheel are the characters that will print. Model 2121 Time Recorder User’s Guide 4.2 Before setting type wheels, observe the center position of wheels, as shown by the arrows below. This releases the print wheels, allowing you to turn them. Set the Printed Day and Time 4.1 Locate and press the red overthrow lever until it clicks. It will click distinctly when it locks place. Model 2121 Time Recorder User’s Guide 3.2 While pushing the lock lever down, lift the entire type section as shown below until it locks into place horizontally. Lift the Type Section 3.1 Locate the lock lever on either side of the type section behind the clock face. Model 2121 Time Recorder User’s Guide 2.4 Place your hands on both sides of the cover and pull it toward you to remove it. See attached instructions if you will be installing on wall. This guide is available to download at: Mount Clock in Suitable Location Must be within 6 feet of AC power source (unswitched) and conveniently located for your employees. Model 2121 Time Recorder User’s Guide Start Here Complete these steps to setup your new time recorder 1. To purchase the appropriate accessories for your Model 2121 time recorder, contact your local Lathem dealer or visit us at. For maximum results, only use Lathem accessories specifically designed to fit your time recorder. Model 2121 Time Recorder User’s Guide Ordering Accessories Lathem time recorders fulfill a wide range of timekeeping requirements. Service information is also included for replacing certain parts. This guide contains all the information you need for setting up and operating your new time recorder. Should you ever need assistance, please let us know. Mechanical Time Recorder Model 2121 User’s GuideĬontents Thank you for choosing the Lathem 2121 time recorder. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |